DTS XD10 Spezifikationen Seite 124
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
XD10 Cinema Media Player, Installation and Operating Guide Version 1.0
G.5. Subtitle Projector Installation
The subtitle projector installation consists of two pieces of hardware: c Projector (DTS-CSP),
d external mask assembly (DTS-EMA), which includes hardware for mounting to the projector booth
wall or ceiling. Most installations will occur in the projection booth. If no other alternative exists, the
projector may be installed in the auditorium.
Note: The DTS-CSP Subtitle Projector MUST be installed upside down.
When installing projector, ensure there is easy access for cleaning the lens and changing the
lamp.
An assistant is needed to help hold the projector when it is attached to the mount.
G.5.1. Installation Tools
Adjustable wrench Drill with ¼ inch (6.3 mm) bit
Various screwdrivers Hex driver 5/32 inch (13.1 mm)
16 mm socket wrench
PRECAUTIONS
It is the installer’s responsibility to evaluate the area selected for mounting the DTS-CSP projector.
Special care must be taken when mounting the projector to the wall. The correct fasteners and a wall
rated to support 25 lbs. (9 kg) must be chosen. The composition and strength of the wall must be
evaluated so that the proper fasteners are used. Adequate reinforcement should be added if the wall
is not strong enough. Consultation with a carpenter is highly recommended. Also, when not using
the DTS mount, consult a carpenter to construct appropriate mounting for the DTS-CSP.
To avoid overheating of the projector, adequate airspace is required. Six inches (15.24 cm) are
required on all sides (left, right, front, and rear) and 12 inches (30.98) is required above and below.
A second person is necessary to hold and support the projector in place during the tightening
p
rocedure.
Failure to follow the procedure set forth in this manual will void the warranty, if any, provided by
DTS with respect to the DTS-CSP subtitling projector.
The installer shall be responsible for any injury or damage resulting from installer’s failure to follow
p
rocedure set forth in the manual, and DTS shall have no responsibility wha
t
-so-ever for any injury
or damage resulting from installer’s failure to follow procedure set forth in this manual.
G.5.2. Installation Procedure
Use this procedure to install the subtitle projector into the projection booth.
1. Verify you have all hardware needed for the DTS-CSP installation.
• One DTS-EMA mask/mount adapter and one DTS-CSP subtitle projector.
• One bracket, wall mounting plate, and arm for mounting the CSP/EMA to the wall.
2. Assemble the bracket and arm to the DTS-EMA.
a. Connect the arm assembly to the DTS-EMA. Place mounting foot so that arm can pivot
upward.
Cinema Subtitling (CSS) Option Document #: 9301E692001.0
G-8
- Film-Tech 1
- XD10 Cinema Media Player 2
- Introduction 8
- DTS Customer Service 9
- Returning Units for Service 10
- Installation Checklist 11
- Completed Task Refer to: 12
- 1. Operational Overview 13
- 1.2. Basic Operation 14
- 1.2.5. CD-ROM Read Error 16
- 1.2.7. Running a Show 16
- 1.2.8. Changeover 16
- 1.3. Routine Maintenance 17
- 1.4. After the Show 17
- 1.5.2. LCD Playscreen 18
- 1.6. Menus 19
- Using the Menus 20
- Test Patterns: 21
- 1.7. Playback 22
- 1.7.2. Video 23
- 1.7.3. CSP Language 25
- 1.7.4. Contents 26
- 1.7.5. CSP Lamp Status 26
- 1.8. System Setup 27
- 1.8.2. Audio Setup 28
- 1.8.3. Video Setup 30
- 1.8.4. CSP Setup 33
- Patterns: 34
- 1.8.5. Automation Setup 35
- 1.8.6. System Options 42
- 1.9. Info 44
- 1.11. Check Procedures 48
- 2. Installation 49
- 2.2. System Components 50
- Drawing Number 51
- (in Appendix B) 51
- 2.4. Installation Procedures 53
- 2.5. XD10 Connectors 55
- 2.6. Options List 58
- 3. Calibration and Setup 59
- 3.2.3. Mono Surround 61
- 3.4. Verifying Operation 62
- 3.4.2. Ch 63
- 4. Specifications 65
- 4.1. Inputs 65
- 4.2. Audio Outputs 65
- 4.3. Other Connectors 66
- 4.4. DVD ROM Drives 67
- 4.5. Hard Drive 67
- 4.6. User Interface 68
- Specifications 69
- 4.8. XD10 Block Diagrams 70
- XD10 with VIDEO OPTION 71
- 5.1. Routine Maintenance 73
- 5.2.3. Volume too loud 74
- 5.3.3. Determining roll-down 75
- 5.4. Inside the DTS XD10 76
- Figure 5-1. XD10 Top View 77
- A.2. Replacement Parts 80
- B. Installation Diagrams 81
- Bracket 94
- C. XD10 Menu Structure 97
- • Set Projector 102
- [ 0 ] pixels 102
- D. Language Management 107
- Appendix 107
- D.2.1. XD10 Operation 108
- D.2.2. Trailers 108
- D.3. Subtitle Languages 109
- E. DTS Track Specifications 111
- F.1.3. Debug Procedure 115
- G.3. DTS-EMA Assembly 119
- 15.94 cm) 120
- 30.48 cm) 120
- 45.72 cm) 120
- 16mm w/ 2mm pitch) 120
- PRECAUTIONS 124
- Subtitle Area 131
- Sc r een 131
- Press both down and 136
- G.8. DTS-EMA Maintenance 137
- No subtitles 138
- No Rear Window captions 140
- No narration audio 140
- G.12. Testing Subtitles 141
- G.13. Testing Narration 141
- H. Technical Notes 143
- TN-E550 145
- August 6, 2002 146
- K. Hultgren 146
- DTS MARQUEE SIGN ORDER FORM 151
- WARRANTY 152
- □ No □ 152
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.223 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern